FULL FOOD CODE:
Each HANDWASHING SINK or group of adjacent HANDWASHING SINKS shall be provided with: (A) Individual, disposable towels; (Pf) (B) A continuous towel system that supplies the user with a clean towel;(Pf) or (C) A heated-air hand drying device.(Pf) (D) A hand drying device that employs an air-knife system that delivers high velocity pressurized air at ambient temperatures.(Pf)

FULL FOOD CODE:
Outer openings of a FOOD ESTABLISHMENT shall be protected against the entry of insects and rodents. Unless otherwise allowed by law.

FULL FOOD CODE:
FOOD shall be protected from contamination by storing the FOOD: (1) In a clean, dry location; (2) Where it is not exposed to splash, dust, or other contamination; and (3) At least 15 cm (6 inches) above the floor, unless otherwise approved.

FULL FOOD CODE:
During pauses in FOOD preparation or dispensing, UTENSILS shall be stored: (A) In the FOOD with their handles above the top of the FOOD and the container; (B) In FOOD that is not POTENTIALLY HAZARDOUS with their handles above the top of the FOOD within containers or EQUIPMENT that can be closed, such as bins of sugar, flour, or cinnamon; (C) On a clean portion of the FOOD preparation table or cooking EQUIPMENT (D) In running water, such as dipper well. (E) In a clean, protected location if the UTENSILS, such as ice scoops, are used only with a FOOD that is not POTENTIALLY HAZARDOUS; or (F) In a container of water maintained at a temperature of at least 135° F.

FULL FOOD CODE:
Outer openings of a FOOD ESTABLISHMENT shall be protected against the entry of insects and rodents. Unless otherwise allowed by law.

FULL FOOD CODE:
FOOD shall be protected from contamination by storing the FOOD: (1) In a clean, dry location; (2) Where it is not exposed to splash, dust, or other contamination; and (3) At least 15 cm (6 inches) above the floor, unless otherwise approved.

FULL FOOD CODE:
Except during preparation, cooking, or cooling, or when time is used as the public health control POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD) shall be maintained: (A) 135ºF or above, except that roasts properly cooked and cooled may be held at a temperature of 130ºF; or (P) (B) At 41ºF or less (P)

FULL FOOD CODE:
A chemical SANITIZER used in a SANITIZING solution for a manual or mechanical operation shall meet these limits or as otherwise approved: (P) Chlorine ppm pH<10 pH<8 25 120 F 120 F 50 100 F 75 F 100 55 F 55 F Iodine a concentration of between 12.5 and 25 ppm and minimum temp of 75 F and pH of 5 or less or meets manufacturer's specifications. (P) Quats minimum temperature of 75 F, hardness of 500 ppm or less and meet manufacturers use directions. (P)

FULL FOOD CODE:
POISONOUS OR TOXIC MATERIALS shall be: (A) Used according to: (1) LAW and this Code, (2) Manufacturer's use directions included in labeling, and, for a pesticide, manufacturer's label instructions that state that use is allowed in a FOOD ESTABLISHMENT, (P) (3) The conditions of certification, if certification is required, for use of the pest control materials, (P) and (4) Additional conditions that may be established by the REGULATORY AUTHORITY; and (B) Applied so that: (1) A HAZARD to EMPLOYEES or other PERSONS is not constituted, (P) and (2) Contamination including toxic residues due to drip, drain, fog, splash or spray on FOOD, EQUIPMENT, UTENSILS, LINENS, AND SINGLE-SERVICE AND SINGLE-USE ARTICLES is prevented, and for a RESTRICTED USE PESTICIDE, this is achieved by: (P) (a) Removing the items, (P) (b) Covering the items with impermeable covers, (P) or (c) Taking other appropriate preventive actions, (P) and (d) Cleaning and SANITIZING EQUIPMENT and UTENSILS after the application. (P) (C) A RESTRICTED USE PESTICIDE shall be applied only by an applicator certified as defined in 7 USC 136 Definitions, (e) Certified Applicator, of the Federal Insecticide, Fungicide, and Rodenticide Act, or a PERSON under the direct supervision of a certified applicator. (Pf)

FULL FOOD CODE:
(A) A HANDWASHING SINK shall be maintained so that it is accessible at all times for EMPLOYEE use and used for no other purpose. (Pf) (B) An automatic handwashing facility shall be used in accordance with manufacturer's instructions. (Pf)

FULL FOOD CODE:
(A) EQUIPMENT FOOD-CONTACT SURFACES and UTENSILS shall be clean to sight and touch. (Pf) (B) The FOOD-CONTACT SURFACES of cooking EQUIPMENT and pans shall be kept free of encrusted grease deposits and other soil accumulations. (C) NonFOOD-CONTACT SURFACES of EQUIPMENT shall be kept free of an accumulation of dust, dirt, FOOD residue, and other debris.

FULL FOOD CODE:
NonFOOD-CONTACT SURFACES of EQUIPMENT shall be cleaned at a frequency necessary to preclude accumulation of soil residues.

FULL FOOD CODE:
During pauses in FOOD preparation or dispensing, UTENSILS shall be stored: (A) In the FOOD with their handles above the top of the FOOD and the container; (B) In FOOD that is not POTENTIALLY HAZARDOUS with their handles above the top of the FOOD within containers or EQUIPMENT that can be closed, such as bins of sugar, flour, or cinnamon; (C) On a clean portion of the FOOD preparation table or cooking EQUIPMENT (D) In running water, such as dipper well. (E) In a clean, protected location if the UTENSILS, such as ice scoops, are used only with a FOOD that is not POTENTIALLY HAZARDOUS; or (F) In a container of water maintained at a temperature of at least 135° F.

FULL FOOD CODE:
After use, mops shall be placed in a position that allows them to air-dry without soiling walls, EQUIPMENT, or supplies.

FULL FOOD CODE:
FOOD shall be protected from contamination by storing the FOOD: (1) In a clean, dry location; (2) Where it is not exposed to splash, dust, or other contamination; and (3) At least 15 cm (6 inches) above the floor, unless otherwise approved.

FULL FOOD CODE:
FOOD EMPLOYEES shall properly wash their hands and exposed portions of their arms for at least 20 seconds and thoroughly rinsing with clean water. EMPLOYEES shall pay particular attention to the areas underneath the fingernails and between the fingers. (P)

FULL FOOD CODE:
(A) EQUIPMENT FOOD-CONTACT SURFACES and UTENSILS shall be clean to sight and touch. (Pf) (B) The FOOD-CONTACT SURFACES of cooking EQUIPMENT and pans shall be kept free of encrusted grease deposits and other soil accumulations. (C) NonFOOD-CONTACT SURFACES of EQUIPMENT shall be kept free of an accumulation of dust, dirt, FOOD residue, and other debris.

FULL FOOD CODE:
(A) A HANDWASHING SINK shall be maintained so that it is accessible at all times for EMPLOYEE use and used for no other purpose. (Pf) (B) An automatic handwashing facility shall be used in accordance with manufacturer's instructions. (Pf)

FULL FOOD CODE:
FOOD EMPLOYEES shall clean their hands in a HANDWASHING SINK or APPROVED automatic handwashing facility and may not clean their hands in a sink used for FOOD preparation or WAREWASHING, or in a service sink or a curbed cleaning facility used for the disposal of mop water and similar liquid waste. (Pf)

FULL FOOD CODE:
During pauses in FOOD preparation or dispensing, UTENSILS shall be stored: (A) In the FOOD with their handles above the top of the FOOD and the container; (B) In FOOD that is not POTENTIALLY HAZARDOUS with their handles above the top of the FOOD within containers or EQUIPMENT that can be closed, such as bins of sugar, flour, or cinnamon; (C) On a clean portion of the FOOD preparation table or cooking EQUIPMENT (D) In running water, such as dipper well. (E) In a clean, protected location if the UTENSILS, such as ice scoops, are used only with a FOOD that is not POTENTIALLY HAZARDOUS; or (F) In a container of water maintained at a temperature of at least 135° F.

FULL FOOD CODE:
(A) PHYSICAL FACILITIES shall be cleaned as often as necessary to keep them clean. (B) Except spill cleanup, cleaning shall be done during periods when the least amount of FOOD is exposed such as after closing.

FULL FOOD CODE:
Except during preparation, cooking, or cooling, or when time is used as the public health control POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD) shall be maintained: (A) 135ºF or above, except that roasts properly cooked and cooled may be held at a temperature of 130ºF; or (P) (B) At 41ºF or less (P)

FULL FOOD CODE:
POISONOUS OR TOXIC MATERIALS shall be: (A) Used according to: (1) LAW and this Code, (2) Manufacturer's use directions included in labeling, and, for a pesticide, manufacturer's label instructions that state that use is allowed in a FOOD ESTABLISHMENT, (P) (3) The conditions of certification, if certification is required, for use of the pest control materials, (P) and (4) Additional conditions that may be established by the REGULATORY AUTHORITY; and (B) Applied so that: (1) A HAZARD to EMPLOYEES or other PERSONS is not constituted, (P) and (2) Contamination including toxic residues due to drip, drain, fog, splash or spray on FOOD, EQUIPMENT, UTENSILS, LINENS, AND SINGLE-SERVICE AND SINGLE-USE ARTICLES is prevented, and for a RESTRICTED USE PESTICIDE, this is achieved by: (P) (a) Removing the items, (P) (b) Covering the items with impermeable covers, (P) or (c) Taking other appropriate preventive actions, (P) and (d) Cleaning and SANITIZING EQUIPMENT and UTENSILS after the application. (P) (C) A RESTRICTED USE PESTICIDE shall be applied only by an applicator certified as defined in 7 USC 136 Definitions, (e) Certified Applicator, of the Federal Insecticide, Fungicide, and Rodenticide Act, or a PERSON under the direct supervision of a certified applicator. (Pf)

FULL FOOD CODE:
(A) A HANDWASHING SINK shall be maintained so that it is accessible at all times for EMPLOYEE use and used for no other purpose. (Pf) (B) An automatic handwashing facility shall be used in accordance with manufacturer's instructions. (Pf)

FULL FOOD CODE:
(A) EQUIPMENT FOOD-CONTACT SURFACES and UTENSILS shall be clean to sight and touch. (Pf) (B) The FOOD-CONTACT SURFACES of cooking EQUIPMENT and pans shall be kept free of encrusted grease deposits and other soil accumulations. (C) NonFOOD-CONTACT SURFACES of EQUIPMENT shall be kept free of an accumulation of dust, dirt, FOOD residue, and other debris.

FULL FOOD CODE:
Each HANDWASHING SINK or group of 2 adjacent HANDWASHING SINKS shall be provided with a supply of hand cleaning liquid, powder, or bar soap. (Pf)

FULL FOOD CODE:
The presence of insects, rodents, and other pests shall be controlled to minimize their presence on the PREMISES. by: (A) Routinely inspecting incoming shipments of FOOD and supplies; (B) Routinely inspecting the PREMISES for evidence of pests; (C) Using methods, if pests are found, such as trapping devices or other means of pest control as specified.(Pf) (D) Eliminating harborage conditions.

FULL FOOD CODE:
Sec. 2129. (1) All food establishments shall employ a minimum of 1 managerial employee as a food safety manager, who must be an individual who is currently certified under a personnel certification program accredited by the American National Standards Institute, utilizing the Conference for Food Protection standards: (2) Beginning January 14, 2017 and every 5 years thereafter, a certified food safety manager who supervises the operations of a food service establishment shall have completed a food safety training program containing an allergen awareness component that has been approved by the department. A food service establishment shall retain records on the site of the food service establishment documenting compliance of its certified food safety managers with this subsection.

FULL FOOD CODE:
During pauses in FOOD preparation or dispensing, UTENSILS shall be stored: (A) In the FOOD with their handles above the top of the FOOD and the container; (B) In FOOD that is not POTENTIALLY HAZARDOUS with their handles above the top of the FOOD within containers or EQUIPMENT that can be closed, such as bins of sugar, flour, or cinnamon; (C) On a clean portion of the FOOD preparation table or cooking EQUIPMENT (D) In running water, such as dipper well. (E) In a clean, protected location if the UTENSILS, such as ice scoops, are used only with a FOOD that is not POTENTIALLY HAZARDOUS; or (F) In a container of water maintained at a temperature of at least 135° F.

FULL FOOD CODE:
(A) PHYSICAL FACILITIES shall be cleaned as often as necessary to keep them clean. (B) Except spill cleanup, cleaning shall be done during periods when the least amount of FOOD is exposed such as after closing.

FULL FOOD CODE:
NonFOOD-CONTACT SURFACES of EQUIPMENT shall be cleaned at a frequency necessary to preclude accumulation of soil residues.

FULL FOOD CODE:
Except during preparation, cooking, or cooling, or when time is used as the public health control POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD) shall be maintained: (A) 135ºF or above, except that roasts properly cooked and cooled may be held at a temperature of 130ºF; or (P) (B) At 41ºF or less (P)

FULL FOOD CODE:
A chemical SANITIZER used in a SANITIZING solution for a manual or mechanical operation shall meet these limits or as otherwise approved: (P) Chlorine ppm pH<10 pH<8 25 120 F 120 F 50 100 F 75 F 100 55 F 55 F Iodine a concentration of between 12.5 and 25 ppm and minimum temp of 75 F and pH of 5 or less or meets manufacturer's specifications. (P) Quats minimum temperature of 75 F, hardness of 500 ppm or less and meet manufacturers use directions. (P)

FULL FOOD CODE:
FOOD shall only contact surfaces of EQUIPMENT and UTENSILS that are cleaned and SANITIZED, or SINGLE-SERVICE and SINGLE-USE ARTICLES. (P)

FULL FOOD CODE:
Except during preparation, cooking, or cooling, or when time is used as the public health control POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD) shall be maintained: (A) 135ºF or above, except that roasts properly cooked and cooled may be held at a temperature of 130ºF; or (P) (B) At 41ºF or less (P)

FULL FOOD CODE:
(A) A HANDWASHING SINK shall be maintained so that it is accessible at all times for EMPLOYEE use and used for no other purpose. (Pf) (B) An automatic handwashing facility shall be used in accordance with manufacturer's instructions. (Pf)

FULL FOOD CODE:
(A) EQUIPMENT FOOD-CONTACT SURFACES and UTENSILS shall be clean to sight and touch. (Pf) (B) The FOOD-CONTACT SURFACES of cooking EQUIPMENT and pans shall be kept free of encrusted grease deposits and other soil accumulations. (C) NonFOOD-CONTACT SURFACES of EQUIPMENT shall be kept free of an accumulation of dust, dirt, FOOD residue, and other debris.

FULL FOOD CODE:
The presence of insects, rodents, and other pests shall be controlled to minimize their presence on the PREMISES. by: (A) Routinely inspecting incoming shipments of FOOD and supplies; (B) Routinely inspecting the PREMISES for evidence of pests; (C) Using methods, if pests are found, such as trapping devices or other means of pest control as specified.(Pf) (D) Eliminating harborage conditions.

FULL FOOD CODE:
(A) PHYSICAL FACILITIES shall be cleaned as often as necessary to keep them clean. (B) Except spill cleanup, cleaning shall be done during periods when the least amount of FOOD is exposed such as after closing.

FULL FOOD CODE:
(A) Intake and exhaust air ducts shall be cleaned and filters changed so they are not a source of contamination by dust, dirt, and other materials. (B) If vented to the outside, ventilation systems may not create a public health HAZARD or nuisance or unLAWful discharge.

FULL FOOD CODE:
Sec. 2129. (1) All food establishments shall employ a minimum of 1 managerial employee as a food safety manager, who must be an individual who is currently certified under a personnel certification program accredited by the American National Standards Institute, utilizing the Conference for Food Protection standards: (2) Beginning January 14, 2017 and every 5 years thereafter, a certified food safety manager who supervises the operations of a food service establishment shall have completed a food safety training program containing an allergen awareness component that has been approved by the department. A food service establishment shall retain records on the site of the food service establishment documenting compliance of its certified food safety managers with this subsection.

FULL FOOD CODE:
During pauses in FOOD preparation or dispensing, UTENSILS shall be stored: (A) In the FOOD with their handles above the top of the FOOD and the container; (B) In FOOD that is not POTENTIALLY HAZARDOUS with their handles above the top of the FOOD within containers or EQUIPMENT that can be closed, such as bins of sugar, flour, or cinnamon; (C) On a clean portion of the FOOD preparation table or cooking EQUIPMENT (D) In running water, such as dipper well. (E) In a clean, protected location if the UTENSILS, such as ice scoops, are used only with a FOOD that is not POTENTIALLY HAZARDOUS; or (F) In a container of water maintained at a temperature of at least 135° F.

FULL FOOD CODE:
FOOD EMPLOYEES shall clean their hands and exposed portions of their arms as specified under § 2-301.12 immediately before engaging in FOOD preparation including working with exposed FOOD, clean EQUIPMENT and UTENSILS, and unwrapped SINGLE-SERVICE and SINGLE-USE ARTICLES (P) and: (A) After touching bare human body parts other than clean hands and clean, exposed portions of arms; (P) (B) After using the toilet room; (P) (C) After caring for or handling SERVICE ANIMALS or aquatic animals as specified in ¶ 2-403.11(B); (P). (D) Except as specified in ¶ 2-401.11(B), after coughing, sneezing, using a handkerchief or disposable tissue, using tobacco, eating, or drinking; (P) (E) After handling soiled EQUIPMENT or UTENSILS; (P) (F) During FOOD preparation, as often as necessary to remove soil and contamination and to prevent cross contamination when changing tasks; (P) (G) When switching between working with raw FOOD and working with READY-TO-EAT FOOD; (P) (H) Before donning gloves for working with FOOD; (P) and (I) After engaging in other activities that contaminate the hands. (P)

FULL FOOD CODE:
Except during preparation, cooking, or cooling, or when time is used as the public health control POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD) shall be maintained: (A) 135ºF or above, except that roasts properly cooked and cooled may be held at a temperature of 130ºF; or (P) (B) At 41ºF or less (P)

FULL FOOD CODE:
FOOD shall only contact surfaces of EQUIPMENT and UTENSILS that are cleaned and SANITIZED, or SINGLE-SERVICE and SINGLE-USE ARTICLES. (P)

FULL FOOD CODE:
(A) A HANDWASHING SINK shall be maintained so that it is accessible at all times for EMPLOYEE use and used for no other purpose. (Pf) (B) An automatic handwashing facility shall be used in accordance with manufacturer's instructions. (Pf)

FULL FOOD CODE:
NonFOOD-CONTACT SURFACES of EQUIPMENT shall be cleaned at a frequency necessary to preclude accumulation of soil residues.

FULL FOOD CODE:
(A) Intake and exhaust air ducts shall be cleaned and filters changed so they are not a source of contamination by dust, dirt, and other materials. (B) If vented to the outside, ventilation systems may not create a public health HAZARD or nuisance or unLAWful discharge.

FULL FOOD CODE:
Sec. 2129. (1) All food establishments shall employ a minimum of 1 managerial employee as a food safety manager, who must be an individual who is currently certified under a personnel certification program accredited by the American National Standards Institute, utilizing the Conference for Food Protection standards: (2) Beginning January 14, 2017 and every 5 years thereafter, a certified food safety manager who supervises the operations of a food service establishment shall have completed a food safety training program containing an allergen awareness component that has been approved by the department. A food service establishment shall retain records on the site of the food service establishment documenting compliance of its certified food safety managers with this subsection.

FULL FOOD CODE:
(A) EQUIPMENT FOOD-CONTACT SURFACES and UTENSILS shall be clean to sight and touch. (Pf) (B) The FOOD-CONTACT SURFACES of cooking EQUIPMENT and pans shall be kept free of encrusted grease deposits and other soil accumulations. (C) NonFOOD-CONTACT SURFACES of EQUIPMENT shall be kept free of an accumulation of dust, dirt, FOOD residue, and other debris.

FULL FOOD CODE:
FOOD EMPLOYEES shall wear hair restraints such as hats, hair coverings or nets, beard restraints, and clothing that covers body hair, that are designed and worn to effectively keep their hair from contacting exposed FOOD; clean EQUIPMENT, UTENSILS, and LINENS; or unwrapped SINGLE-SERVICE or SINGLE-USE ARTICLES.

FULL FOOD CODE:
During pauses in FOOD preparation or dispensing, UTENSILS shall be stored: (A) In the FOOD with their handles above the top of the FOOD and the container; (B) In FOOD that is not POTENTIALLY HAZARDOUS with their handles above the top of the FOOD within containers or EQUIPMENT that can be closed, such as bins of sugar, flour, or cinnamon; (C) On a clean portion of the FOOD preparation table or cooking EQUIPMENT (D) In running water, such as dipper well. (E) In a clean, protected location if the UTENSILS, such as ice scoops, are used only with a FOOD that is not POTENTIALLY HAZARDOUS; or (F) In a container of water maintained at a temperature of at least 135° F.

FULL FOOD CODE:
(A) PHYSICAL FACILITIES shall be cleaned as often as necessary to keep them clean. (B) Except spill cleanup, cleaning shall be done during periods when the least amount of FOOD is exposed such as after closing.

FULL FOOD CODE:
(A) Cooling shall be accomplished in accordance with the time and temperature criteria specified under § 3-501.14 by using one or more of the following methods based on the type of FOOD being cooled: (1) Placing the FOOD in shallow pans; (Pf) (2) Separating the FOOD into smaller or thinner portions; (Pf) (3) Using rapid cooling EQUIPMENT; (Pf) (4) Stirring the FOOD in a container placed in an ice water bath; (Pf) (5) Using containers that facilitate heat transfer; (Pf) (6) Adding ice as an ingredient; (Pf) or (7) Other effective methods. (Pf) (B) When placed in cooling or cold holding EQUIPMENT, FOOD containers in which FOOD is being cooled shall be: (1) Arranged in the EQUIPMENT to provide maximum heat transfer through the container walls; and (2) Loosely covered, or uncovered if protected from overhead contamination as specified under Subparagraph 3-305.11(A)(2), during the cooling period to facilitate heat transfer from the surface of the FOOD.

FULL FOOD CODE:
Each HANDWASHING SINK or group of 2 adjacent HANDWASHING SINKS shall be provided with a supply of hand cleaning liquid, powder, or bar soap. (Pf)

FULL FOOD CODE:
(A) A HANDWASHING SINK shall be maintained so that it is accessible at all times for EMPLOYEE use and used for no other purpose. (Pf) (B) An automatic handwashing facility shall be used in accordance with manufacturer's instructions. (Pf)

FULL FOOD CODE:
(A) PHYSICAL FACILITIES shall be cleaned as often as necessary to keep them clean. (B) Except spill cleanup, cleaning shall be done during periods when the least amount of FOOD is exposed such as after closing.

FULL FOOD CODE:
(A) Cloths that are in use for wiping FOOD spills on TABLEWARE shall be maintained dry and used for no other purpose. (B) Cloths in-use for wiping counters and equipment shall be held between uses in a chemical sanitizer solution, and laundered daily. (C) Cloths in-use for wiping surfaces in contact with raw animal FOODS shall be kept separate from cloths used for other purposes. (D) Dry wiping cloths and the chemical sanitizing solutions shall be free of FOOD debris or visible soil. (E) Containers of chemical sanitizing solutions shall be stored off the floor and used in a manner that prevents contamination of FOOD, EQUIPMENT, UTENSILS, LINENS, SINGLE-SERVICE, or SINGLE-USE ARTICLES. (E) SINGLE-USE disposable sanitizer wipes shall be used in accordance lable instructions.

FULL FOOD CODE:
Sec. 2129. (1) All food establishments shall employ a minimum of 1 managerial employee as a food safety manager, who must be an individual who is currently certified under a personnel certification program accredited by the American National Standards Institute, utilizing the Conference for Food Protection standards: (2) Beginning January 14, 2017 and every 5 years thereafter, a certified food safety manager who supervises the operations of a food service establishment shall have completed a food safety training program containing an allergen awareness component that has been approved by the department. A food service establishment shall retain records on the site of the food service establishment documenting compliance of its certified food safety managers with this subsection.

FULL FOOD CODE:
During pauses in FOOD preparation or dispensing, UTENSILS shall be stored: (A) In the FOOD with their handles above the top of the FOOD and the container; (B) In FOOD that is not POTENTIALLY HAZARDOUS with their handles above the top of the FOOD within containers or EQUIPMENT that can be closed, such as bins of sugar, flour, or cinnamon; (C) On a clean portion of the FOOD preparation table or cooking EQUIPMENT (D) In running water, such as dipper well. (E) In a clean, protected location if the UTENSILS, such as ice scoops, are used only with a FOOD that is not POTENTIALLY HAZARDOUS; or (F) In a container of water maintained at a temperature of at least 135° F.

FULL FOOD CODE:
NonFOOD-CONTACT SURFACES of EQUIPMENT shall be cleaned at a frequency necessary to preclude accumulation of soil residues.

FULL FOOD CODE:
(A) Intake and exhaust air ducts shall be cleaned and filters changed so they are not a source of contamination by dust, dirt, and other materials. (B) If vented to the outside, ventilation systems may not create a public health HAZARD or nuisance or unLAWful discharge.

FULL FOOD CODE:
(A) FOOD shall be protected from cross contamination by: (1) Except as specified in (1)(c) below, separating raw animal FOODS during storage, preparation, holding, and display from: (a) Raw READY-TO-EAT FOOD including other raw animal FOOD such as FISH for sushi or MOLLUSCAN SHELLFISH, or other raw READY-TO-EAT FOOD such as fruits and vegetables,(P) and (b) Cooked READY-TO-EAT FOOD; (P) (c) Frozen, commercially processed and packaged raw animal FOOD may be stored or displayed with or above frozen, commercially processed and packaged, ready-to-eat food. (2) Except when combined as ingredients, separating types of raw animal FOODS from each other such as beef, FISH, lamb, pork, and POULTRY during storage, preparation, holding, and display by: (a) Using separate EQUIPMENT for each type, (P) or (b) Arranging each type of FOOD in EQUIPMENT so that cross contamination of one type with another is prevented, (P) and (c) Preparing each type of FOOD at different times or in separate areas; (P)

FULL FOOD CODE:
Except during preparation, cooking, or cooling, or when time is used as the public health control POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD) shall be maintained: (A) 135ºF or above, except that roasts properly cooked and cooled may be held at a temperature of 130ºF; or (P) (B) At 41ºF or less (P)

FULL FOOD CODE:
(A) EQUIPMENT FOOD-CONTACT SURFACES and UTENSILS shall be clean to sight and touch. (Pf) (B) The FOOD-CONTACT SURFACES of cooking EQUIPMENT and pans shall be kept free of encrusted grease deposits and other soil accumulations. (C) NonFOOD-CONTACT SURFACES of EQUIPMENT shall be kept free of an accumulation of dust, dirt, FOOD residue, and other debris.

FULL FOOD CODE:
Each HANDWASHING SINK or group of adjacent HANDWASHING SINKS shall be provided with: (A) Individual, disposable towels; (Pf) (B) A continuous towel system that supplies the user with a clean towel;(Pf) or (C) A heated-air hand drying device.(Pf) (D) A hand drying device that employs an air-knife system that delivers high velocity pressurized air at ambient temperatures.(Pf)

FULL FOOD CODE:
(A) A HANDWASHING SINK shall be maintained so that it is accessible at all times for EMPLOYEE use and used for no other purpose. (Pf) (B) An automatic handwashing facility shall be used in accordance with manufacturer's instructions. (Pf)

FULL FOOD CODE:
Each HANDWASHING SINK or group of 2 adjacent HANDWASHING SINKS shall be provided with a supply of hand cleaning liquid, powder, or bar soap. (Pf)

FULL FOOD CODE:
NonFOOD-CONTACT SURFACES of EQUIPMENT shall be cleaned at a frequency necessary to preclude accumulation of soil residues.

FULL FOOD CODE:
(A) Areas designated for EMPLOYEES to eat, drink, and use tobacco shall be located so that FOOD, EQUIPMENT, LINENS, and SINGLE-SERVICE and SINGLE-USE ARTICLES are protected from contamination. (B) Lockers or other suitable facilities shall be located in a designated room or area where contamination of FOOD, EQUIPMENT, UTENSILS, LINENS, and SINGLE-SERVICE and SINGLE-USE ARTICLES can not occur.

FULL FOOD CODE:
(A) Intake and exhaust air ducts shall be cleaned and filters changed so they are not a source of contamination by dust, dirt, and other materials. (B) If vented to the outside, ventilation systems may not create a public health HAZARD or nuisance or unLAWful discharge.

FULL FOOD CODE:
(A) Cloths that are in use for wiping FOOD spills on TABLEWARE shall be maintained dry and used for no other purpose. (B) Cloths in-use for wiping counters and equipment shall be held between uses in a chemical sanitizer solution, and laundered daily. (C) Cloths in-use for wiping surfaces in contact with raw animal FOODS shall be kept separate from cloths used for other purposes. (D) Dry wiping cloths and the chemical sanitizing solutions shall be free of FOOD debris or visible soil. (E) Containers of chemical sanitizing solutions shall be stored off the floor and used in a manner that prevents contamination of FOOD, EQUIPMENT, UTENSILS, LINENS, SINGLE-SERVICE, or SINGLE-USE ARTICLES. (E) SINGLE-USE disposable sanitizer wipes shall be used in accordance lable instructions.

FULL FOOD CODE:
(A) PHYSICAL FACILITIES shall be cleaned as often as necessary to keep them clean. (B) Except spill cleanup, cleaning shall be done during periods when the least amount of FOOD is exposed such as after closing.

FULL FOOD CODE:
During pauses in FOOD preparation or dispensing, UTENSILS shall be stored: (A) In the FOOD with their handles above the top of the FOOD and the container; (B) In FOOD that is not POTENTIALLY HAZARDOUS with their handles above the top of the FOOD within containers or EQUIPMENT that can be closed, such as bins of sugar, flour, or cinnamon; (C) On a clean portion of the FOOD preparation table or cooking EQUIPMENT (D) In running water, such as dipper well. (E) In a clean, protected location if the UTENSILS, such as ice scoops, are used only with a FOOD that is not POTENTIALLY HAZARDOUS; or (F) In a container of water maintained at a temperature of at least 135° F.

FULL FOOD CODE:
Chemical SANITIZERS and other chemical antimicrobials applied to FOOD-CONTACT SURFACES shall meet the requirements specified in this code. (P)

FULL FOOD CODE:
Except during preparation, cooking, or cooling, or when time is used as the public health control POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD) shall be maintained: (A) 135ºF or above, except that roasts properly cooked and cooled may be held at a temperature of 130ºF; or (P) (B) At 41ºF or less (P)

FULL FOOD CODE:
(A) A HANDWASHING SINK shall be maintained so that it is accessible at all times for EMPLOYEE use and used for no other purpose. (Pf) (B) An automatic handwashing facility shall be used in accordance with manufacturer's instructions. (Pf)

FULL FOOD CODE:
(A) Intake and exhaust air ducts shall be cleaned and filters changed so they are not a source of contamination by dust, dirt, and other materials. (B) If vented to the outside, ventilation systems may not create a public health HAZARD or nuisance or unLAWful discharge.

FULL FOOD CODE:
(A) Areas designated for EMPLOYEES to eat, drink, and use tobacco shall be located so that FOOD, EQUIPMENT, LINENS, and SINGLE-SERVICE and SINGLE-USE ARTICLES are protected from contamination. (B) Lockers or other suitable facilities shall be located in a designated room or area where contamination of FOOD, EQUIPMENT, UTENSILS, LINENS, and SINGLE-SERVICE and SINGLE-USE ARTICLES can not occur.

FULL FOOD CODE:
FOOD shall be protected from contamination by storing the FOOD: (1) In a clean, dry location; (2) Where it is not exposed to splash, dust, or other contamination; and (3) At least 15 cm (6 inches) above the floor, unless otherwise approved.

FULL FOOD CODE:
(A) Equipment FOOD-CONTACT SURFACES and UTENSILS shall be cleaned: (1) Except as specified in ¶ (B) of this section, before each use with a different type of raw animal FOOD such as beef, FISH, lamb, pork, or POULTRY; (P) (2) Each time there is a change from working with raw FOODS to working with READY-TO-EAT FOODS; (P) (3) Between uses with raw fruits and vegetables and with POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD); (P) (4) Before using or storing a FOOD TEMPERATURE MEASURING DEVICE; (P) and (5) At any time during the operation when contamination may have occurred. (P) (B) Subparagraph (A)(1) of this section does not apply if the FOOD-CONTACT SURFACE or UTENSIL is in contact with a succession of different raw animal FOODS each requiring a higher cooking temperature as specified under § 3-401.11 than the previous FOOD, such as preparing raw FISH followed by cutting raw poultry on the same cutting board. (C) Except as specified in ¶ (D) of this section, if used with POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD), EQUIPMENT FOOD-CONTACT SURFACES and UTENSILS shall be cleaned throughout the day at least every 4 hours. (P) (D) Except when dry cleaning methods are used as specified under § 4-603.11, surfaces of UTENSILS and EQUIPMENT contacting FOOD that is not POTENTIALLY HAZARDOUS (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD) shall be cleaned: (1) At any time when contamination may have occurred; (2) At least every 24 hours for iced tea dispensers and CONSUMER self-service UTENSILS such as tongs, scoops, or ladles; (3) Before restocking CONSUMER self-service EQUIPMENT and UTENSILS such as condiment dispensers and display containers; and (4) In EQUIPMENT such as ice bins and BEVERAGE dispensing nozzles and enclosed components of EQUIPMENT such as ice makers, cooking oil storage tanks and distribution lines, BEVERAGE and syrup dispensing lines or tubes, coffee bean grinders, and water vending EQUIPMENT: (a) At a frequency specified by the manufacturer, or (b) Absent manufacturer specifications, at a frequency necessary to preclude accumulation of soil or mold.