city of detroit logo

DETROIT RESTAURANT INSPECTIONS

HOMEABOUT
This site is deprecated, please go to detroitrestaurantinspections.netlify.app to view the maintained site.

Subway #26842
9655 Gratiot Ave.

Food Service Establishment

StatusOpen
License typeFixed Establishment
State license number078355
OwnerHussein Obeid
Complexity levelUnknown
Review frequencyEvery 150 days

7 Inspections
Since 8-1-2016

12-10-2019
Routine Inspection

OutcomeNot compliant
4 violations cited :
Code 5-202.12
Handwashing facility lack of hot water
FULL FOOD CODE:
(A) A handwashing sink shall be equipped to provide water at a temperature of at least 38°C (100°F) through a mixing valve or combination faucet. (Pf) (B) A steam mixing valve may not be used at a handwashing sink. (C) A self-closing, slow-closing, or metering faucet shall provide a flow of water for at least 15 seconds without the need to reactivate the faucet. (D) An automatic handwashing facility shall be installed in accordance with manufacturer's instructions.
Priority
Not corrected
Code 3-305.11
Food item(s) in storage exposed to dust splash or other contaminates
FULL FOOD CODE:
FOOD shall be protected from contamination by storing the FOOD: (1) In a clean, dry location; (2) Where it is not exposed to splash, dust, or other contamination; and (3) At least 15 cm (6 inches) above the floor, unless otherwise approved.
Core
Not corrected
Code 6-202.15
Outer opening(s) door s not sealed to prevent pest entry
FULL FOOD CODE:
Outer openings of a FOOD ESTABLISHMENT shall be protected against the entry of insects and rodents. Unless otherwise allowed by law.
Core
Not corrected
Code 4-204.112
Thermometer(s) refrigeration not provided
FULL FOOD CODE:
(A) In a mechanically refrigerated or hot FOOD storage unit, the sensor of a TEMPERATURE MEASURING DEVICE shall be located to measure the air temperature in the warmest part of a mechanically refrigerated unit and in the coolest part of a hot FOOD storage unit. (B) Cold or hot holding EQUIPMENT used for POTENTIALLY HAZARDOUS FOOD shall be designed to include and shall be equipped with at least one integral or permanently affixed TEMPERATURE MEASURING DEVICE that is located to allow easy viewing of the device's temperature display (EXCEPT, heat lamps, cold plates, steam tables, or other equipment where it is not practical). (C) TEMPERATURE MEASURING DEVICES shall be designed to be easily readable. (D) FOOD TEMPERATURE MEASURING DEVICES and water TEMPERATURE MEASURING DEVICES on WAREWASHING machines shall have a numerical scale, printed record, or digital readout in increments no greater than 1C or 2F in the intended range of use. (Pf)
Core
Not corrected

05-13-2019
Routine Inspection

OutcomeNot compliant
4 violations cited :
Code 3-501.16
Cold food item(s) stored above 41 degrees f
FULL FOOD CODE:
Except during preparation, cooking, or cooling, or when time is used as the public health control POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD) shall be maintained: (A) 135ºF or above, except that roasts properly cooked and cooled may be held at a temperature of 130ºF; or (P) (B) At 41ºF or less (P)
Priority
Corrected on 5-14-2019
Code 5-202.12
Handwashing facility lack of hot water
FULL FOOD CODE:
(A) A handwashing sink shall be equipped to provide water at a temperature of at least 38°C (100°F) through a mixing valve or combination faucet. (Pf) (B) A steam mixing valve may not be used at a handwashing sink. (C) A self-closing, slow-closing, or metering faucet shall provide a flow of water for at least 15 seconds without the need to reactivate the faucet. (D) An automatic handwashing facility shall be installed in accordance with manufacturer's instructions.
Priority
Not corrected
Code 6-303.11
Lighting intensity not maintained
FULL FOOD CODE:
Light of the proper intensity shall be provided as specified.
Core
Not corrected
Code 6-202.15
Outer opening(s) door s not sealed to prevent pest entry
FULL FOOD CODE:
Outer openings of a FOOD ESTABLISHMENT shall be protected against the entry of insects and rodents. Unless otherwise allowed by law.
Core
Not corrected

12-11-2018
Routine Inspection

OutcomeNot compliant
4 violations cited :
Code 4-501.11
Expand for full food code definition
FULL FOOD CODE:
EQUIPMENT shall be maintained in a state of repair and condition that meets the requirements of the code.
Core
Not corrected
Code 6-303.11
Expand for full food code definition
FULL FOOD CODE:
Light of the proper intensity shall be provided as specified.
Core
Not corrected
Code 6-202.15
Expand for full food code definition
FULL FOOD CODE:
Outer openings of a FOOD ESTABLISHMENT shall be protected against the entry of insects and rodents. Unless otherwise allowed by law.
Core
Not corrected
Code 5-205.15
Expand for full food code definition
FULL FOOD CODE:
A PLUMBING SYSTEM shall be: (A) Repaired according to LAW; (P) and (B) Maintained in good repair.
Core
Not corrected

04-25-2018
Routine Inspection

OutcomeNot compliant
2 violations cited :
Code 4-302.14
Sanitizer test kit damaged
FULL FOOD CODE:
A test kit or other device that accurately measures the concentration in mg/L of SANITIZING solutions shall be provided. (Pf)
Priority Foundation
Not corrected
Code 4-204.112
Thermometer(s) refrigeration not provided
FULL FOOD CODE:
(A) In a mechanically refrigerated or hot FOOD storage unit, the sensor of a TEMPERATURE MEASURING DEVICE shall be located to measure the air temperature in the warmest part of a mechanically refrigerated unit and in the coolest part of a hot FOOD storage unit. (B) Cold or hot holding EQUIPMENT used for POTENTIALLY HAZARDOUS FOOD shall be designed to include and shall be equipped with at least one integral or permanently affixed TEMPERATURE MEASURING DEVICE that is located to allow easy viewing of the device's temperature display (EXCEPT, heat lamps, cold plates, steam tables, or other equipment where it is not practical). (C) TEMPERATURE MEASURING DEVICES shall be designed to be easily readable. (D) FOOD TEMPERATURE MEASURING DEVICES and water TEMPERATURE MEASURING DEVICES on WAREWASHING machines shall have a numerical scale, printed record, or digital readout in increments no greater than 1C or 2F in the intended range of use. (Pf)
Core
Not corrected

09-27-2017
Routine Inspection

OutcomeNot compliant
3 violations cited :
Code 3-501.16
Cold food item(s) stored above 41 degrees f
FULL FOOD CODE:
Except during preparation, cooking, or cooling, or when time is used as the public health control POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD) shall be maintained: (A) 135ºF or above, except that roasts properly cooked and cooled may be held at a temperature of 130ºF; or (P) (B) At 41ºF or less (P)
Priority
Corrected on 9-28-2017
Code 4-204.112
Thermometer(s) not provided
FULL FOOD CODE:
(A) In a mechanically refrigerated or hot FOOD storage unit, the sensor of a TEMPERATURE MEASURING DEVICE shall be located to measure the air temperature in the warmest part of a mechanically refrigerated unit and in the coolest part of a hot FOOD storage unit. (B) Cold or hot holding EQUIPMENT used for POTENTIALLY HAZARDOUS FOOD shall be designed to include and shall be equipped with at least one integral or permanently affixed TEMPERATURE MEASURING DEVICE that is located to allow easy viewing of the device's temperature display (EXCEPT, heat lamps, cold plates, steam tables, or other equipment where it is not practical). (C) TEMPERATURE MEASURING DEVICES shall be designed to be easily readable. (D) FOOD TEMPERATURE MEASURING DEVICES and water TEMPERATURE MEASURING DEVICES on WAREWASHING machines shall have a numerical scale, printed record, or digital readout in increments no greater than 1C or 2F in the intended range of use. (Pf)
Priority Foundation
Not corrected
Code 3-501.13
Frozen food(s) for thawing stored above 41 degrees f thawed or partially thawed at room temperature
FULL FOOD CODE:
POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD) shall be thawed: Under refrigeration, or under cool running water (<70° F), or as part of cooking process, and total accumulated time above 41° F, for thawed portions, shall not exceed 4 hours. Any thawing procedure may be used for immediate service for individual consumers order of READY-TO-EAT foods.
Core
Corrected on 9-28-2017

02-28-2017
Routine Inspection

OutcomeNot compliant
2 violations cited :
Code 4-204.112
Thermometer(s) refrigeration not provided
FULL FOOD CODE:
(A) In a mechanically refrigerated or hot FOOD storage unit, the sensor of a TEMPERATURE MEASURING DEVICE shall be located to measure the air temperature in the warmest part of a mechanically refrigerated unit and in the coolest part of a hot FOOD storage unit. (B) Cold or hot holding EQUIPMENT used for POTENTIALLY HAZARDOUS FOOD shall be designed to include and shall be equipped with at least one integral or permanently affixed TEMPERATURE MEASURING DEVICE that is located to allow easy viewing of the device's temperature display (EXCEPT, heat lamps, cold plates, steam tables, or other equipment where it is not practical). (C) TEMPERATURE MEASURING DEVICES shall be designed to be easily readable. (D) FOOD TEMPERATURE MEASURING DEVICES and water TEMPERATURE MEASURING DEVICES on WAREWASHING machines shall have a numerical scale, printed record, or digital readout in increments no greater than 1C or 2F in the intended range of use. (Pf)
Core
Not corrected
Code 6-303.11
Lighting intensity not maintained
FULL FOOD CODE:
Light of the proper intensity shall be provided as specified.
Core
Not corrected

08-24-2016
Routine Inspection

OutcomeNot compliant
1 violation cited :
Code 4-602.11
Food-contact surface(s) and utensil(s) not cleaned
FULL FOOD CODE:
(A) Equipment FOOD-CONTACT SURFACES and UTENSILS shall be cleaned: (1) Except as specified in ¶ (B) of this section, before each use with a different type of raw animal FOOD such as beef, FISH, lamb, pork, or POULTRY; (P) (2) Each time there is a change from working with raw FOODS to working with READY-TO-EAT FOODS; (P) (3) Between uses with raw fruits and vegetables and with POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD); (P) (4) Before using or storing a FOOD TEMPERATURE MEASURING DEVICE; (P) and (5) At any time during the operation when contamination may have occurred. (P) (B) Subparagraph (A)(1) of this section does not apply if the FOOD-CONTACT SURFACE or UTENSIL is in contact with a succession of different raw animal FOODS each requiring a higher cooking temperature as specified under § 3-401.11 than the previous FOOD, such as preparing raw FISH followed by cutting raw poultry on the same cutting board. (C) Except as specified in ¶ (D) of this section, if used with POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD), EQUIPMENT FOOD-CONTACT SURFACES and UTENSILS shall be cleaned throughout the day at least every 4 hours. (P) (D) Except when dry cleaning methods are used as specified under § 4-603.11, surfaces of UTENSILS and EQUIPMENT contacting FOOD that is not POTENTIALLY HAZARDOUS (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD) shall be cleaned: (1) At any time when contamination may have occurred; (2) At least every 24 hours for iced tea dispensers and CONSUMER self-service UTENSILS such as tongs, scoops, or ladles; (3) Before restocking CONSUMER self-service EQUIPMENT and UTENSILS such as condiment dispensers and display containers; and (4) In EQUIPMENT such as ice bins and BEVERAGE dispensing nozzles and enclosed components of EQUIPMENT such as ice makers, cooking oil storage tanks and distribution lines, BEVERAGE and syrup dispensing lines or tubes, coffee bean grinders, and water vending EQUIPMENT: (a) At a frequency specified by the manufacturer, or (b) Absent manufacturer specifications, at a frequency necessary to preclude accumulation of soil or mold.
Core
Not corrected
About inspections
A restaurant is compliant when zero Priority or Priority Foundation violations are cited during an inspection, or when all are corrected; Core violations will be reviewed at the next routine inspection and are not required to be corrected to be in compliance.
Built using open data | Last updated 2023-04-25