FULL FOOD CODE:
(A) Cooked POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD) shall be cooled: (1) Within 2 hours, from 135ºF to 70ºF; and (P) (2) Within 4 hours, from 70ºF to 41ºF or less (P) (B) POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD) prepared from ingredients at ambient temperature shall be cooled within 4 hours to 41F or less. (P) (C) POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD) received in compliance with LAWS allowing a temperature above 41ºF during shipment from the supplier shall be cooled within 4 hours to 41ºF or less. (P)

FULL FOOD CODE:
If an animal FOOD such as beef, EGGS, FISH, lamb, milk, pork, POULTRY, or shellfish is served or sold raw, undercooked, or without otherwise being processed to eliminate pathogens, either in a READY-TO-EAT form or as an ingredient in another READY-TO-EAT FOOD, the PERMIT HOLDER shall inform CONSUMERS of the significantly increased RISK of consuming such FOODS, by using menu advisories, brochures, lable statements, table tents, placards, or other effective written means. (Pf) FOOD LAW SEC 6149 ...The food establishment may provide the following statement on selection information so that it is made pulblicly available: "Ask your server about menu items that are cooked to order or served raw. Consuming raw or undercooked, meats, poultry, shellfish, or eggs may increase your risk of foodborne illness." The statements must be in a minimum of 11 point font and in a color that provides a clear contrast to background.

FULL FOOD CODE:
(A) Cooling shall be accomplished in accordance with the time and temperature criteria specified under § 3-501.14 by using one or more of the following methods based on the type of FOOD being cooled: (1) Placing the FOOD in shallow pans; (Pf) (2) Separating the FOOD into smaller or thinner portions; (Pf) (3) Using rapid cooling EQUIPMENT; (Pf) (4) Stirring the FOOD in a container placed in an ice water bath; (Pf) (5) Using containers that facilitate heat transfer; (Pf) (6) Adding ice as an ingredient; (Pf) or (7) Other effective methods. (Pf) (B) When placed in cooling or cold holding EQUIPMENT, FOOD containers in which FOOD is being cooled shall be: (1) Arranged in the EQUIPMENT to provide maximum heat transfer through the container walls; and (2) Loosely covered, or uncovered if protected from overhead contamination as specified under Subparagraph 3-305.11(A)(2), during the cooling period to facilitate heat transfer from the surface of the FOOD.

FULL FOOD CODE:
Dead or trapped birds, insects, rodents, and other pests shall be removed from control devices and the PREMISES at a frequency that prevents their accumulation, decomposition, or the attraction of pests.

FULL FOOD CODE:
Cleaned EQUIPMENT and UTENSILS, laundered LINENS, and SINGLE-SERVICE and SINGLE-USE ARTICLES shall be stored in an approved manner and location.

FULL FOOD CODE:
Dead or trapped birds, insects, rodents, and other pests shall be removed from control devices and the PREMISES at a frequency that prevents their accumulation, decomposition, or the attraction of pests.

FULL FOOD CODE:
(A) In a mechanically refrigerated or hot FOOD storage unit, the sensor of a TEMPERATURE MEASURING DEVICE shall be located to measure the air temperature in the warmest part of a mechanically refrigerated unit and in the coolest part of a hot FOOD storage unit. (B) Cold or hot holding EQUIPMENT used for POTENTIALLY HAZARDOUS FOOD shall be designed to include and shall be equipped with at least one integral or permanently affixed TEMPERATURE MEASURING DEVICE that is located to allow easy viewing of the device's temperature display (EXCEPT, heat lamps, cold plates, steam tables, or other equipment where it is not practical). (C) TEMPERATURE MEASURING DEVICES shall be designed to be easily readable. (D) FOOD TEMPERATURE MEASURING DEVICES and water TEMPERATURE MEASURING DEVICES on WAREWASHING machines shall have a numerical scale, printed record, or digital readout in increments no greater than 1C or 2F in the intended range of use. (Pf)

FULL FOOD CODE:
NonFOOD-CONTACT SURFACES of EQUIPMENT shall be cleaned at a frequency necessary to preclude accumulation of soil residues.

FULL FOOD CODE:
Except as otherwise approved, light bulbs shall be shielded, coated, or otherwise shatter-resistant in areas where there is exposed FOOD; clean EQUIPMENT, UTENSILS, and LINENS; or unwrapped SINGLE-SERVICE and SINGLE-USE ARTICLES.

FULL FOOD CODE:
FOOD EMPLOYEES shall clean their hands and exposed portions of their arms as specified under § 2-301.12 immediately before engaging in FOOD preparation including working with exposed FOOD, clean EQUIPMENT and UTENSILS, and unwrapped SINGLE-SERVICE and SINGLE-USE ARTICLES (P) and: (A) After touching bare human body parts other than clean hands and clean, exposed portions of arms; (P) (B) After using the toilet room; (P) (C) After caring for or handling SERVICE ANIMALS or aquatic animals as specified in ¶ 2-403.11(B); (P). (D) Except as specified in ¶ 2-401.11(B), after coughing, sneezing, using a handkerchief or disposable tissue, using tobacco, eating, or drinking; (P) (E) After handling soiled EQUIPMENT or UTENSILS; (P) (F) During FOOD preparation, as often as necessary to remove soil and contamination and to prevent cross contamination when changing tasks; (P) (G) When switching between working with raw FOOD and working with READY-TO-EAT FOOD; (P) (H) Before donning gloves for working with FOOD; (P) and (I) After engaging in other activities that contaminate the hands. (P)

FULL FOOD CODE:
(A) Equipment FOOD-CONTACT SURFACES and UTENSILS shall be cleaned: (1) Except as specified in ¶ (B) of this section, before each use with a different type of raw animal FOOD such as beef, FISH, lamb, pork, or POULTRY; (P) (2) Each time there is a change from working with raw FOODS to working with READY-TO-EAT FOODS; (P) (3) Between uses with raw fruits and vegetables and with POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD); (P) (4) Before using or storing a FOOD TEMPERATURE MEASURING DEVICE; (P) and (5) At any time during the operation when contamination may have occurred. (P) (B) Subparagraph (A)(1) of this section does not apply if the FOOD-CONTACT SURFACE or UTENSIL is in contact with a succession of different raw animal FOODS each requiring a higher cooking temperature as specified under § 3-401.11 than the previous FOOD, such as preparing raw FISH followed by cutting raw poultry on the same cutting board. (C) Except as specified in ¶ (D) of this section, if used with POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD), EQUIPMENT FOOD-CONTACT SURFACES and UTENSILS shall be cleaned throughout the day at least every 4 hours. (P) (D) Except when dry cleaning methods are used as specified under § 4-603.11, surfaces of UTENSILS and EQUIPMENT contacting FOOD that is not POTENTIALLY HAZARDOUS (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD) shall be cleaned: (1) At any time when contamination may have occurred; (2) At least every 24 hours for iced tea dispensers and CONSUMER self-service UTENSILS such as tongs, scoops, or ladles; (3) Before restocking CONSUMER self-service EQUIPMENT and UTENSILS such as condiment dispensers and display containers; and (4) In EQUIPMENT such as ice bins and BEVERAGE dispensing nozzles and enclosed components of EQUIPMENT such as ice makers, cooking oil storage tanks and distribution lines, BEVERAGE and syrup dispensing lines or tubes, coffee bean grinders, and water vending EQUIPMENT: (a) At a frequency specified by the manufacturer, or (b) Absent manufacturer specifications, at a frequency necessary to preclude accumulation of soil or mold.

FULL FOOD CODE:
The PERSON IN CHARGE shall ensure that employees, practices and policies are in compliance with the code. (Pf)

FULL FOOD CODE:
(A) EQUIPMENT FOOD-CONTACT SURFACES and UTENSILS shall be clean to sight and touch. (Pf) (B) The FOOD-CONTACT SURFACES of cooking EQUIPMENT and pans shall be kept free of encrusted grease deposits and other soil accumulations. (C) NonFOOD-CONTACT SURFACES of EQUIPMENT shall be kept free of an accumulation of dust, dirt, FOOD residue, and other debris.

FULL FOOD CODE:
(A) READY-TO-EAT, POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD) prepared and held refrigerated for more than 24 hours in a FOOD ESTABLISHMENT shall be clearly marked at the time of preparation to indicate the date or day by which the FOOD shall be consumed. (Pf) (B) A container of refrigerated, commercially prepared READY-TO-EAT POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD) shall be clearly marked, at the time the original container is opened in a FOOD ESTABLISHMENT, to indicate the date or day by which the FOOD shall be consumed. (Pf) A date marking system that does not exceed 7 days, including date of preparation, or opening is to be used. (Pf)

FULL FOOD CODE:
The PERSON IN CHARGE shall demonstrate this knowledge by compliance with this Code, by being a certified FOOD protection manager who has shown proficiency of required information through passing a test that is part of an ACCREDITED PROGRAM, or by responding correctly to the inspector's questions as they relate to the specific FOOD operation. (Pf)

FULL FOOD CODE:
(A) PHYSICAL FACILITIES shall be cleaned as often as necessary to keep them clean. (B) Except spill cleanup, cleaning shall be done during periods when the least amount of FOOD is exposed such as after closing.

FULL FOOD CODE:
EQUIPMENT shall be maintained in a state of repair and condition that meets the requirements of the code.

FULL FOOD CODE:
FOOD EMPLOYEES shall wear hair restraints such as hats, hair coverings or nets, beard restraints, and clothing that covers body hair, that are designed and worn to effectively keep their hair from contacting exposed FOOD; clean EQUIPMENT, UTENSILS, and LINENS; or unwrapped SINGLE-SERVICE or SINGLE-USE ARTICLES.

FULL FOOD CODE:
NonFOOD-CONTACT SURFACES of EQUIPMENT shall be cleaned at a frequency necessary to preclude accumulation of soil residues.

FULL FOOD CODE:
A WAREWASHING machine; the compartments of sinks, basins, or other receptacles used for washing and rinsing EQUIPMENT, UTENSILS, or raw FOODS, or laundering wiping cloths; and drainboards or other EQUIPMENT used to substitute for drainboards shall be cleaned as required.

FULL FOOD CODE:
POISONOUS OR TOXIC MATERIALS shall be: (A) Used according to: (1) LAW and this Code, (2) Manufacturer's use directions included in labeling, and, for a pesticide, manufacturer's label instructions that state that use is allowed in a FOOD ESTABLISHMENT, (P) (3) The conditions of certification, if certification is required, for use of the pest control materials, (P) and (4) Additional conditions that may be established by the REGULATORY AUTHORITY; and (B) Applied so that: (1) A HAZARD to EMPLOYEES or other PERSONS is not constituted, (P) and (2) Contamination including toxic residues due to drip, drain, fog, splash or spray on FOOD, EQUIPMENT, UTENSILS, LINENS, AND SINGLE-SERVICE AND SINGLE-USE ARTICLES is prevented, and for a RESTRICTED USE PESTICIDE, this is achieved by: (P) (a) Removing the items, (P) (b) Covering the items with impermeable covers, (P) or (c) Taking other appropriate preventive actions, (P) and (d) Cleaning and SANITIZING EQUIPMENT and UTENSILS after the application. (P) (C) A RESTRICTED USE PESTICIDE shall be applied only by an applicator certified as defined in 7 USC 136 Definitions, (e) Certified Applicator, of the Federal Insecticide, Fungicide, and Rodenticide Act, or a PERSON under the direct supervision of a certified applicator. (Pf)

FULL FOOD CODE:
(A) READY-TO-EAT, POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD) prepared and held refrigerated for more than 24 hours in a FOOD ESTABLISHMENT shall be clearly marked at the time of preparation to indicate the date or day by which the FOOD shall be consumed. (Pf) (B) A container of refrigerated, commercially prepared READY-TO-EAT POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD) shall be clearly marked, at the time the original container is opened in a FOOD ESTABLISHMENT, to indicate the date or day by which the FOOD shall be consumed. (Pf) A date marking system that does not exceed 7 days, including date of preparation, or opening is to be used. (Pf)

FULL FOOD CODE:
(A) A HANDWASHING SINK shall be maintained so that it is accessible at all times for EMPLOYEE use and used for no other purpose. (Pf) (B) An automatic handwashing facility shall be used in accordance with manufacturer's instructions. (Pf)

FULL FOOD CODE:
NonFOOD-CONTACT SURFACES of EQUIPMENT shall be cleaned at a frequency necessary to preclude accumulation of soil residues.

FULL FOOD CODE:
(A) LINENS that do not come in direct contact with FOOD shall be laundered between operations if they become wet, sticky, or visibly soiled. (B) Cloth gloves used as specified in ¶ 3-304.15(D) shall be laundered before being used with a different type of raw animal FOOD such as beef, FISH, lamb, pork or POULTRY. (C) LINENS and napkins that are used as specified under § 3-304.13 and cloth napkins shall be laundered between each use. (D) Wet wiping cloths shall be laundered daily. (E) Dry wiping cloths shall be laundered as necessary to prevent contamination of FOOD and clean serving UTENSILS.

FULL FOOD CODE:
(A) Equipment FOOD-CONTACT SURFACES and UTENSILS shall be cleaned: (1) Except as specified in ¶ (B) of this section, before each use with a different type of raw animal FOOD such as beef, FISH, lamb, pork, or POULTRY; (P) (2) Each time there is a change from working with raw FOODS to working with READY-TO-EAT FOODS; (P) (3) Between uses with raw fruits and vegetables and with POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD); (P) (4) Before using or storing a FOOD TEMPERATURE MEASURING DEVICE; (P) and (5) At any time during the operation when contamination may have occurred. (P) (B) Subparagraph (A)(1) of this section does not apply if the FOOD-CONTACT SURFACE or UTENSIL is in contact with a succession of different raw animal FOODS each requiring a higher cooking temperature as specified under § 3-401.11 than the previous FOOD, such as preparing raw FISH followed by cutting raw poultry on the same cutting board. (C) Except as specified in ¶ (D) of this section, if used with POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD), EQUIPMENT FOOD-CONTACT SURFACES and UTENSILS shall be cleaned throughout the day at least every 4 hours. (P) (D) Except when dry cleaning methods are used as specified under § 4-603.11, surfaces of UTENSILS and EQUIPMENT contacting FOOD that is not POTENTIALLY HAZARDOUS (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD) shall be cleaned: (1) At any time when contamination may have occurred; (2) At least every 24 hours for iced tea dispensers and CONSUMER self-service UTENSILS such as tongs, scoops, or ladles; (3) Before restocking CONSUMER self-service EQUIPMENT and UTENSILS such as condiment dispensers and display containers; and (4) In EQUIPMENT such as ice bins and BEVERAGE dispensing nozzles and enclosed components of EQUIPMENT such as ice makers, cooking oil storage tanks and distribution lines, BEVERAGE and syrup dispensing lines or tubes, coffee bean grinders, and water vending EQUIPMENT: (a) At a frequency specified by the manufacturer, or (b) Absent manufacturer specifications, at a frequency necessary to preclude accumulation of soil or mold.

FULL FOOD CODE:
(A) PHYSICAL FACILITIES shall be cleaned as often as necessary to keep them clean. (B) Except spill cleanup, cleaning shall be done during periods when the least amount of FOOD is exposed such as after closing.

FULL FOOD CODE:
Cleaned EQUIPMENT and UTENSILS, laundered LINENS, and SINGLE-SERVICE and SINGLE-USE ARTICLES shall be stored in an approved manner and location.

FULL FOOD CODE:
Dead or trapped birds, insects, rodents, and other pests shall be removed from control devices and the PREMISES at a frequency that prevents their accumulation, decomposition, or the attraction of pests.

FULL FOOD CODE:
(A) FOOD shall be protected from cross contamination by: (1) Except as specified in (1)(c) below, separating raw animal FOODS during storage, preparation, holding, and display from: (a) Raw READY-TO-EAT FOOD including other raw animal FOOD such as FISH for sushi or MOLLUSCAN SHELLFISH, or other raw READY-TO-EAT FOOD such as fruits and vegetables,(P) and (b) Cooked READY-TO-EAT FOOD; (P) (c) Frozen, commercially processed and packaged raw animal FOOD may be stored or displayed with or above frozen, commercially processed and packaged, ready-to-eat food. (2) Except when combined as ingredients, separating types of raw animal FOODS from each other such as beef, FISH, lamb, pork, and POULTRY during storage, preparation, holding, and display by: (a) Using separate EQUIPMENT for each type, (P) or (b) Arranging each type of FOOD in EQUIPMENT so that cross contamination of one type with another is prevented, (P) and (c) Preparing each type of FOOD at different times or in separate areas; (P)

FULL FOOD CODE:
POISONOUS OR TOXIC MATERIALS shall be: (A) Used according to: (1) LAW and this Code, (2) Manufacturer's use directions included in labeling, and, for a pesticide, manufacturer's label instructions that state that use is allowed in a FOOD ESTABLISHMENT, (P) (3) The conditions of certification, if certification is required, for use of the pest control materials, (P) and (4) Additional conditions that may be established by the REGULATORY AUTHORITY; and (B) Applied so that: (1) A HAZARD to EMPLOYEES or other PERSONS is not constituted, (P) and (2) Contamination including toxic residues due to drip, drain, fog, splash or spray on FOOD, EQUIPMENT, UTENSILS, LINENS, AND SINGLE-SERVICE AND SINGLE-USE ARTICLES is prevented, and for a RESTRICTED USE PESTICIDE, this is achieved by: (P) (a) Removing the items, (P) (b) Covering the items with impermeable covers, (P) or (c) Taking other appropriate preventive actions, (P) and (d) Cleaning and SANITIZING EQUIPMENT and UTENSILS after the application. (P) (C) A RESTRICTED USE PESTICIDE shall be applied only by an applicator certified as defined in 7 USC 136 Definitions, (e) Certified Applicator, of the Federal Insecticide, Fungicide, and Rodenticide Act, or a PERSON under the direct supervision of a certified applicator. (Pf)

FULL FOOD CODE:
Except during preparation, cooking, or cooling, or when time is used as the public health control POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD) shall be maintained: (A) 135ºF or above, except that roasts properly cooked and cooled may be held at a temperature of 130ºF; or (P) (B) At 41ºF or less (P)

FULL FOOD CODE:
EQUIPMENT for cooling and heating FOOD, and holding cold and hot FOOD, shall be sufficient in number and capacity to provide FOOD temperatures as required. (Pf)

FULL FOOD CODE:
(A) The FOOD-CONTACT SURFACES of cooking and baking EQUIPMENT shall be cleaned at least every 24 hours. This section does not apply to hot oil cooking and filtering EQUIPMENT if it is cleaned as specified in Subparagraph 4-602.11(D)(6). (B) The cavities and door seals of microwave ovens shall be cleaned at least every 24 hours by using the manufacturer's recommended cleaning procedure.

FULL FOOD CODE:
During pauses in FOOD preparation or dispensing, UTENSILS shall be stored: (A) In the FOOD with their handles above the top of the FOOD and the container; (B) In FOOD that is not POTENTIALLY HAZARDOUS with their handles above the top of the FOOD within containers or EQUIPMENT that can be closed, such as bins of sugar, flour, or cinnamon; (C) On a clean portion of the FOOD preparation table or cooking EQUIPMENT (D) In running water, such as dipper well. (E) In a clean, protected location if the UTENSILS, such as ice scoops, are used only with a FOOD that is not POTENTIALLY HAZARDOUS; or (F) In a container of water maintained at a temperature of at least 135° F.

FULL FOOD CODE:
FOOD shall be protected from contamination that may result from a factor or source not specified under Subparts 3-301 - 3-306.

FULL FOOD CODE:
PLUMBING FIXTURES such as HANDWASHING SINKS, toilets, and urinals shall be cleaned as often as necessary to keep them clean.

FULL FOOD CODE:
(A) PHYSICAL FACILITIES shall be cleaned as often as necessary to keep them clean. (B) Except spill cleanup, cleaning shall be done during periods when the least amount of FOOD is exposed such as after closing.

FULL FOOD CODE:
A chemical SANITIZER used in a SANITIZING solution for a manual or mechanical operation shall meet these limits or as otherwise approved: (P) Chlorine ppm pH<10 pH<8 25 120 F 120 F 50 100 F 75 F 100 55 F 55 F Iodine a concentration of between 12.5 and 25 ppm and minimum temp of 75 F and pH of 5 or less or meets manufacturer's specifications. (P) Quats minimum temperature of 75 F, hardness of 500 ppm or less and meet manufacturers use directions. (P)

FULL FOOD CODE:
Working containers used for storing POISONOUS OR TOXIC MATERIALS such as cleaners and SANITIZERS taken from bulk supplies shall be clearly and individually identified with the common name of the material. (Pf)

FULL FOOD CODE:
FOOD shall be protected from contamination by storing the FOOD: (1) In a clean, dry location; (2) Where it is not exposed to splash, dust, or other contamination; and (3) At least 15 cm (6 inches) above the floor, unless otherwise approved.

FULL FOOD CODE:
A chemical SANITIZER used in a SANITIZING solution for a manual or mechanical operation shall meet these limits or as otherwise approved: (P) Chlorine ppm pH<10 pH<8 25 120 F 120 F 50 100 F 75 F 100 55 F 55 F Iodine a concentration of between 12.5 and 25 ppm and minimum temp of 75 F and pH of 5 or less or meets manufacturer's specifications. (P) Quats minimum temperature of 75 F, hardness of 500 ppm or less and meet manufacturers use directions. (P)

FULL FOOD CODE:
The temperature of the wash solution in manual WAREWASHING EQUIPMENT shall be maintained at not less than 110 F or the temperature specified on the cleaning agent manufacturer's label instructions. (Pf)

FULL FOOD CODE:
Sec. 2129. (1) All food establishments shall employ a minimum of 1 managerial employee as a food safety manager, who must be an individual who is currently certified under a personnel certification program accredited by the American National Standards Institute, utilizing the Conference for Food Protection standards: (2) Beginning January 14, 2017 and every 5 years thereafter, a certified food safety manager who supervises the operations of a food service establishment shall have completed a food safety training program containing an allergen awareness component that has been approved by the department. A food service establishment shall retain records on the site of the food service establishment documenting compliance of its certified food safety managers with this subsection.

FULL FOOD CODE:
PLUMBING FIXTURES such as HANDWASHING SINKS, toilets, and urinals shall be cleaned as often as necessary to keep them clean.

FULL FOOD CODE:
(A) PHYSICAL FACILITIES shall be cleaned as often as necessary to keep them clean. (B) Except spill cleanup, cleaning shall be done during periods when the least amount of FOOD is exposed such as after closing.

FULL FOOD CODE:
A chemical SANITIZER used in a SANITIZING solution for a manual or mechanical operation shall meet these limits or as otherwise approved: (P) Chlorine ppm pH<10 pH<8 25 120 F 120 F 50 100 F 75 F 100 55 F 55 F Iodine a concentration of between 12.5 and 25 ppm and minimum temp of 75 F and pH of 5 or less or meets manufacturer's specifications. (P) Quats minimum temperature of 75 F, hardness of 500 ppm or less and meet manufacturers use directions. (P)

FULL FOOD CODE:
Except during preparation, cooking, or cooling, or when time is used as the public health control POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD) shall be maintained: (A) 135ºF or above, except that roasts properly cooked and cooled may be held at a temperature of 130ºF; or (P) (B) At 41ºF or less (P)

FULL FOOD CODE:
Except during preparation, cooking, or cooling, or when time is used as the public health control POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD) shall be maintained: (A) 135ºF or above, except that roasts properly cooked and cooled may be held at a temperature of 130ºF; or (P) (B) At 41ºF or less (P)

FULL FOOD CODE:
(A) FOOD EMPLOYEES shall keep their fingernails trimmed, filed, and maintained so the edges and surfaces are cleanable and not rough. (Pf) (B) Unless wearing intact gloves in good repair, a FOOD EMPLOYEE may not wear fingernail polish or artificial fingernails when working with exposed FOOD. (Pf)

FULL FOOD CODE:
(A) EQUIPMENT FOOD-CONTACT SURFACES and UTENSILS shall be clean to sight and touch. (Pf) (B) The FOOD-CONTACT SURFACES of cooking EQUIPMENT and pans shall be kept free of encrusted grease deposits and other soil accumulations. (C) NonFOOD-CONTACT SURFACES of EQUIPMENT shall be kept free of an accumulation of dust, dirt, FOOD residue, and other debris.

FULL FOOD CODE:
(A) A HANDWASHING SINK shall be maintained so that it is accessible at all times for EMPLOYEE use and used for no other purpose. (Pf) (B) An automatic handwashing facility shall be used in accordance with manufacturer's instructions. (Pf)

FULL FOOD CODE:
FOOD shall be protected from contamination that may result from a factor or source not specified under Subparts 3-301 - 3-306.

FULL FOOD CODE:
The wash, rinse, and SANITIZE solutions shall be maintained clean.

FULL FOOD CODE:
(A) PHYSICAL FACILITIES shall be cleaned as often as necessary to keep them clean. (B) Except spill cleanup, cleaning shall be done during periods when the least amount of FOOD is exposed such as after closing.

FULL FOOD CODE:
NonFOOD-CONTACT SURFACES of EQUIPMENT shall be cleaned at a frequency necessary to preclude accumulation of soil residues.

FULL FOOD CODE:
NonFOOD-CONTACT SURFACES of EQUIPMENT shall be cleaned at a frequency necessary to preclude accumulation of soil residues.

FULL FOOD CODE:
FOOD shall be protected from contamination that may result from a factor or source not specified under Subparts 3-301 - 3-306.

FULL FOOD CODE:
(A) PHYSICAL FACILITIES shall be cleaned as often as necessary to keep them clean. (B) Except spill cleanup, cleaning shall be done during periods when the least amount of FOOD is exposed such as after closing.

FULL FOOD CODE:
(A) An EMPLOYEE shall eat, drink, or use any form of tobacco only in designated areas where the contamination of exposed FOOD; clean EQUIPMENT, UTENSILS, and LINENS; unwrapped SINGLE-SERVICE and SINGLE-USE ARTICLES; or other items needing protection can not result. (B) A FOOD EMPLOYEE may drink from a closed BEVERAGE container if the container is handled to prevent contamination of: (1) The EMPLOYEE'S hands; (2) The container; and (3) Exposed FOOD; clean EQUIPMENT, UTENSILS, and LINENS; and unwrapped SINGLE-SERVICE and SINGLE-USE ARTICLES.