city of detroit logo

DETROIT RESTAURANT INSPECTIONS

HOMEABOUT
This site is deprecated, please go to detroitrestaurantinspections.netlify.app to view the maintained site.

Scarab Club of Detroit
217 Farnsworth St.

Food Service Establishment

StatusOpen
License typeFixed Establishment
State license number034504
OwnerThe Scarab Club Inc.
Complexity levelMedium
Review frequencyEvery 335 days

8 Inspections
Since 8-1-2016

03-06-2023
Routine Inspection

OutcomeCompliant
2 violations cited :
Code 4-602.12
Microwave oven door seals and cavities not cleaned
FULL FOOD CODE:
(A) The FOOD-CONTACT SURFACES of cooking and baking EQUIPMENT shall be cleaned at least every 24 hours. This section does not apply to hot oil cooking and filtering EQUIPMENT if it is cleaned as specified in Subparagraph 4-602.11(D)(6). (B) The cavities and door seals of microwave ovens shall be cleaned at least every 24 hours by using the manufacturer's recommended cleaning procedure.
Core
Not corrected
Code 4-602.13
Nonfood contact surface(s) soiled
FULL FOOD CODE:
NonFOOD-CONTACT SURFACES of EQUIPMENT shall be cleaned at a frequency necessary to preclude accumulation of soil residues.
Core
Not corrected

03-01-2022
Routine Inspection

OutcomeNot compliant
2 violations cited :
Code 5-205.15
Plumbing system water line s not maintained
FULL FOOD CODE:
A PLUMBING SYSTEM shall be: (A) Repaired according to LAW; (P) and (B) Maintained in good repair.
Core
Not corrected
Code 4-803.11
Soiled linen(s) stored improperly
FULL FOOD CODE:
Soiled LINENS shall be kept in clean, nonabsorbent receptacles or clean, washable laundry bags and stored and transported to prevent contamination of FOOD, clean EQUIPMENT, clean UTENSILS, and SINGLE-SERVICE and SINGLE-USE ARTICLES.
Core
Corrected on 3-02-2022

02-09-2021
Routine Inspection

OutcomeCompliant
2 violations cited :
Code 4-903.11
Clean equipment/utensil(s) stored on floor or less than 6 inches above floor
FULL FOOD CODE:
Cleaned EQUIPMENT and UTENSILS, laundered LINENS, and SINGLE-SERVICE and SINGLE-USE ARTICLES shall be stored in an approved manner and location.
Core
Not corrected
Code 6-501.18
sink two compartment
FULL FOOD CODE:
PLUMBING FIXTURES such as HANDWASHING SINKS, toilets, and urinals shall be cleaned as often as necessary to keep them clean.
Core
Not corrected

03-15-2020
COVID19-temp closed

OutcomeCompliant
0 violations cited

11-20-2019
Routine Inspection

OutcomeNot compliant
5 violations cited :
Code 3-101.11
Food adulterated contaminated
FULL FOOD CODE:
FOOD shall be safe, unADULTERATED and honestly presented. (P)
Priority
Corrected on 11-21-2019
Code 5-203.14
Backflow prevention backflow backsiphonage device not provided
FULL FOOD CODE:
A PLUMBING SYSTEM shall be installed to preclude backflow of contaminants into the water supply system at each point of use at the FOOD ESTABLISHMENT by providing an air gap or installing an APPROVED backflow prevention device. (P)
Priority
Not corrected
Code 4-302.12
Food thermometer(s) not provided
FULL FOOD CODE:
(A) FOOD TEMPERATURE MEASURING DEVICES shall be provided and readily accessible for use in ensuring attainment and maintenance of FOOD temperatures as specified under Chapter 3. (Pf) (B) A TEMPERATURE MEASURING DEVICE with a suitable small-diameter probe that is designed to measure the temperature of thin masses shall be provided and readily accessible to accurately measure the temperature in thin FOODS such as MEAT patties and FISH filets. (Pf)
Priority Foundation
Not corrected
Code 4-204.112
Thermometer(s) refrigeration not provided
FULL FOOD CODE:
(A) In a mechanically refrigerated or hot FOOD storage unit, the sensor of a TEMPERATURE MEASURING DEVICE shall be located to measure the air temperature in the warmest part of a mechanically refrigerated unit and in the coolest part of a hot FOOD storage unit. (B) Cold or hot holding EQUIPMENT used for POTENTIALLY HAZARDOUS FOOD shall be designed to include and shall be equipped with at least one integral or permanently affixed TEMPERATURE MEASURING DEVICE that is located to allow easy viewing of the device's temperature display (EXCEPT, heat lamps, cold plates, steam tables, or other equipment where it is not practical). (C) TEMPERATURE MEASURING DEVICES shall be designed to be easily readable. (D) FOOD TEMPERATURE MEASURING DEVICES and water TEMPERATURE MEASURING DEVICES on WAREWASHING machines shall have a numerical scale, printed record, or digital readout in increments no greater than 1C or 2F in the intended range of use. (Pf)
Core
Not corrected
Code 6-501.14
Ventilation system not clean
FULL FOOD CODE:
(A) Intake and exhaust air ducts shall be cleaned and filters changed so they are not a source of contamination by dust, dirt, and other materials. (B) If vented to the outside, ventilation systems may not create a public health HAZARD or nuisance or unLAWful discharge.
Core
Not corrected

12-13-2018
Routine Inspection

OutcomeCompliant
4 violations cited :
Code 3-101.11
Food
FULL FOOD CODE:
FOOD shall be safe, unADULTERATED and honestly presented. (P)
Priority
Corrected on 12-14-2018
Code 3-501.17
Commercially processed ready to eat potentially hazardous food(s) without date of consumption marking
FULL FOOD CODE:
(A) READY-TO-EAT, POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD) prepared and held refrigerated for more than 24 hours in a FOOD ESTABLISHMENT shall be clearly marked at the time of preparation to indicate the date or day by which the FOOD shall be consumed. (Pf) (B) A container of refrigerated, commercially prepared READY-TO-EAT POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD) shall be clearly marked, at the time the original container is opened in a FOOD ESTABLISHMENT, to indicate the date or day by which the FOOD shall be consumed. (Pf) A date marking system that does not exceed 7 days, including date of preparation, or opening is to be used. (Pf)
Priority Foundation
Corrected on 12-14-2018
Code 4-602.13
Nonfood contact surface(s) soiled
FULL FOOD CODE:
NonFOOD-CONTACT SURFACES of EQUIPMENT shall be cleaned at a frequency necessary to preclude accumulation of soil residues.
Core
Not corrected
Code 4-501.14
Warewashing equipment not cleaned
FULL FOOD CODE:
A WAREWASHING machine; the compartments of sinks, basins, or other receptacles used for washing and rinsing EQUIPMENT, UTENSILS, or raw FOODS, or laundering wiping cloths; and drainboards or other EQUIPMENT used to substitute for drainboards shall be cleaned as required.
Core
Not corrected

11-14-2017
Routine Inspection

OutcomeNot compliant
2 violations cited :
Code 5-203.14
Backflow prevention backflow backsiphonage device not provided
FULL FOOD CODE:
A PLUMBING SYSTEM shall be installed to preclude backflow of contaminants into the water supply system at each point of use at the FOOD ESTABLISHMENT by providing an air gap or installing an APPROVED backflow prevention device. (P)
Priority
Not corrected
Code 5-203.11
Handwashing lavatories not provided
FULL FOOD CODE:
(A) A HANDWASHING SINK or an approved automatic handwashing unit shall be provided as necessary for their convenient use by EMPLOYEES in areas specified and not fewer than the number of HANDWASHING SINKS required by LAW shall be provided. (Pf) (B) If APPROVED, when FOOD exposure is limited and HANDWASHING SINKS are not conveniently available, such as in some mobile or TEMPORARY FOOD ESTABLISHMENTS or at some VENDING MACHINE LOCATIONS, EMPLOYEES may use chemically treated towelettes for handwashing.
Priority Foundation
Not corrected

11-09-2016
Routine Inspection

OutcomeCompliant
1 violation cited :
Code 4-602.12
Microwave oven door seals and cavities not cleaned
FULL FOOD CODE:
(A) The FOOD-CONTACT SURFACES of cooking and baking EQUIPMENT shall be cleaned at least every 24 hours. This section does not apply to hot oil cooking and filtering EQUIPMENT if it is cleaned as specified in Subparagraph 4-602.11(D)(6). (B) The cavities and door seals of microwave ovens shall be cleaned at least every 24 hours by using the manufacturer's recommended cleaning procedure.
Core
Not corrected
About inspections
A restaurant is compliant when zero Priority or Priority Foundation violations are cited during an inspection, or when all are corrected; Core violations will be reviewed at the next routine inspection and are not required to be corrected to be in compliance.
Built using open data | Last updated 2023-04-25